LIGHTED TELESCOPING LED EXTENSION INSPECTION MIRROR!! 
Great Tool for plumbers,hvac,janitors, automotive/truck  mechanics or anyone doing maintenance work... 35 inches long with flexible SWIVEL HEAD!

DESCRIPTION:

This paint withstands continuous temperatures up to 1200°F (648°C). It is excellent for use on engine headers, manifolds, furnaces, boilers, metal fireplaces, grills and more. It forms a super durable porcelain-like bond on surfaces at high temperatures and offers excellent resistance to gasoline, rust, salt spray, oil, grease and humidity.

FEATURES:

• Overspray is Reduced
• Porcelain-like Bond at High Temperatures
• Resists Blistering, Peeling, Discoloration, or Loss of Adhesion
• Fast Dry
• Does Not Contain Lead or CFC's

SUITABLE FOR:

• Sink traps

QUIK STEEL-REINFORCED EPOXY PUTTY STICK®

Repair and rebuild anything made of steel!!

Made in U.S.A.

• The ultimate solution for small or

emergency repairs

• Easy-to-use and mistake-proof

• Bonds instantly with superior strength

• Saves hundreds of dollars in repairs

• Belongs in every toolbox

Seals leaks in

Product Description

QUIK STEEL  Epoxy Putty Stick is a fast-setting, industrial-strength polymer

compound that enables permanent repairs to anything

made of steel or other metals. Each handy stick contains

pre-measured portions of activator and base throughout — no

measuring or mixing tools are necessary. As the epoxy is mixed,

the two contrasting colors blend into one color to indicate

complete mixing. The consistency (like modeling clay) eliminates

drips and runs, facilitates adhesion to the substrate, and allows

the material to be shaped and formed as needed before curing

begins. Once functional cure is reached (within minutes after

application), it can be tapped, drilled, sawed, machined, filed,

ground, or painted. QUIK STEEL  cures to a dark gray metallic color.

It is non-rusting. Suitable for interior or exterior use, it is resistant

to water, chemicals, and temperature extremes. QUIK STEEL  contains

no solvents or VOCs. It's non-flammable and releases no noxious

fumes. It won't shrink or pull away. The unused portion stays fresh

for future use when saved in its original package.

Performance Data*

SHELF LIFE AT 75°F (24°C), minimum 24 months

SHORE D HARDNESS AT FULL CURE (24 hrs) 80

LAP SHEAR TENSILE STRENGTH

On steel (1" x 1" x 1/16") 900 lbs (6.2 MPa)

COMPRESSIVE STRENGTH 8,000 psi (55 MPa)

DENSITY 18.5 lb/gal, 2.2 gm/cm3

SHRINKAGE <1%

NON-VOLATILE CONTENT 100%

ELECTRICAL RESISTANCE 30,000 megohms

DIELECTRIC STRENGTH 300 volts/mil

UPPER TEMPERATURE LIMITS

Continuous 250°F (121°C)

Intermittent 300°F (149°C)

CHEMICAL RESISTANCE

Resistant to hydrocarbons, ketones, alcohols, esters,

halocarbons, aqueous salt solutions and dilute acids

and bases.

How To Use:CUT,MIX & APPLY

Certified for use in contact with drinking water.

1.Repairs small engine parts, holes in truck and

Auto gas tanks, seals leaks, fills cracks and

voids in metal.

2.Forms nuts and bolt repairs , stripped threads

And or machines.

3.Repairs metal tools,equipment, housing, ducts

and appliances. Repairs holes in A/C condensation

pan.  Repair pea traps, Pipes etc.RUST PROOF.

REORDER:WINNER IND SUPPLY :1-877-597-6261

WEBSITE: HTTP://WWW.N2WINNERCHEMICAL.COM

Convert-A
converts rusted surfaces into an inert  black polymered surfaces which protects surfaces
and prevents future rusting.

Convert is paintable but painting is not neccesary for great protection.

packaged in a box of 12 aerosols for only  $195.00!

STEP SAFE AEROSOL

STEP SAFE is an ideal coating for Steps, Metal Roofs, Tile, Sidewalks, Vehicles, patios, pavement around a pool, on a boat, boat trailer, in the laundry room, bathroom, and in industrial work spaces where firmer footing is needed. It can be used on steel, fiberglass, treated aluminum, concrete, wood and other surfaces. STEP SAFE will provide a surface with a grit which make slips less likely, even when wet. Special features of this coating include:

* Quick dry and easier on wet feet * Brushes, tools and equipment clean up with soap and water 

Stock Colors are Black and Clear which blends with any surface.

However special colors are available but require minimum orders.

* Applies easily over oil or waterbase primers * STEP SAFE is self priming on most surfaces *

PRECAUTIONS: DO NOT use on garage floors or other areas where vehicles are parked or on smooth glossy surface such as ceramic tile. DO NOT USE in areas where there is continuous standing water. Use STEP SAFE  in the aerosol can for tubs and showers.

PREPARATION: Surface must be clean, dry and free of oil, gas, dirt, soap, rust or mill scale. Clean surface with TSP, rinse thoroughly and let dry. Deteriorating or chalking surfaces should be cleaned with a wire brush, power scraper or sandblast. Ferrous metal does not need a primer unless it is needed for rust resistance. Firm foot will work well over the top of most rust resistant metal primers. Lightly sand Fiberglass or wipe with Acetone before painting. Treat new and smooth concrete with a concrete etch solution before painting. Concrete should not be painted until it is at least 60 days old. Treat Aluminum with a pretreatment compound before painting. STEP SAFE can be used directly on wood surfaces in one or two coats depending upon the porosity of the wood (thin first coat). However, better results may be obtained on exterior wood surfaces primed with a good exterior primer.

PREVIOUSLY PAINTED SURFACES: Dull glossy surfaces with chemical gloss remover, #3 steel wool or 200 grit sandpaper. Wash off all dirt, grease, soap, oil build-up with TSP and water. Rinse thoroughly. Remove loose paint and patch holes and cracks. Spot prime bare spots with appropriate primer or a first coat of thinned STEP SAFE.  WARNING!  If you scrape, sand or remove old paint from any surface, you may release lead dust.  LEAD IS TOXIC.  EXPOSURE TO LEAD DUST CAN CASE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN.  PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.  Wear a NIOSH-approved respirator to control lead exposure.  Carefully clean up with a wet mop or HEPA vacuum.  Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

APPLICATION: STIR OR SHAKE WELL BEFORE USING. Air and surface temperature must be above 50° F during and 8 hours after application. Apply with nylon bristle brush or roller. If a second coat is desired, allow 1 to 2 hours between applications, or until tack free. Dries to the touch in 30 to 40 minutes. Dries hard in 72 hours or more depending on atmospheric temperature. DO NOT USE for airless spray application.  Firm Foot may be sprayed through a conventional spray system, however the grit may plug and can damage spray tips.

TOUCH UP: Touch up can be done with this product or with the aerosol STEP SAFE   in matching colors. Touch up frequency depends upon wear. Allow STEP SAFE  to cure for at least 8 hours before subjecting to light traffic and 48 hours before exposure to heavy use. Do not let water stand on newly painted surface for two weeks.

THINNING: First coat may be thinned with no more than one pint per gallon of water. Second coat should be applied at package consistency. DO NOT ADD ANYTHING TO THIS PRODUCT OTHER THAN WATER.

COVERAGE: 300 to 500 square feet per gallon depending upon surface absorption and smoothness. Coverage greatly increases over nonporous and properly primed surfaces.

CLEAN UP: Clean up with soap and water.

Contains 2-Butoxyethanol (111-76-2).

Vapor harmful. May affect the brain or nervous system causing dizziness, headache or nausea. Causes nose and throat irritation.

NOTICE: Repeated and prolonged exposure to solvents may cause permanent brain and nervous system damage. In addition, inhaling the concentrated contents is harmful and may be fatal. Contains materials which may cause blood, liver and kidney damage.

Use only with adequate ventilation. Do not breathe vapors or spray mist. Ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH approved) during and after application. Failure to wear proper respiratory protection may result in permanent brain and nervous system damage. Follow respirator manufacturer’s directions for respirator use. Avoid contact with eyes, skin and clothing. Wash thoroughly after handling.

FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of contact, immediately flush eyes or skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Get medical attention immediately. Wash clothing before reuse. If swallowed, get medical attention immediately.

If spilled, contain spilled material and remove with inert absorbent. Dispose of contaminated absorbent, container and unused contents in accordance with local, state and federal regulations.

Read Material Safety Data Sheet Before Using This Product!

IMPORTANT! Do not add any materials to this paint other than those specified in these instructions.

DO NOT TRANSFER TO UNLABELED CONTAINER · KEEP OUT OF REACH OF CHILDREN


Click Details for MSDS